MMM
YYYY
Soliton microcomb generation by cavity polygon modes
通过腔多边形模式生成孤子微梳
キャビティポリゴンモードを用いたソリトンマイクロビームの生成
캐비티 다각형 모형을 이용하여 고자 마이크로빔을 생성하다
Generación de haces solitarios utilizando modos poligonos de cavidad
Génération de microfaisceaux Solitons avec un moule polygonal cavité
Создание одиночных микропучков с помощью полостных многоугольных модулей
Botao Fu 付博涛 ¹ ⁴, Renhong Gao 高仁宏 ¹ ⁶, Ni Yao 姚妮 ², Haisu Zhang 张海粟 ³, Chuntao Li 黎春桃 ³, Jintian Lin 林锦添 ¹ ⁵, Min Wang 汪旻 ³, Lingling Qiao 乔玲玲 ¹, Ya Cheng 程亚 ¹ ³ ⁴ ⁶ ⁷
¹ State Key Laboratory of High Field Laser Physics and CAS Center for Excellence in Ultra-Intense Laser Science, Shanghai Institute of Optics and Fine Mechanics (SIOM), Chinese Academy of Sciences (CAS), Shanghai 201800, China
中国 上海 中国科学院上海光学精密机械研究所 强场激光物理国家重点实验室 超强激光科学卓越创新中心
² Research Center for Frontier Fundamental Studies, Zhejiang Lab, Hangzhou 311100, China
中国 杭州 之江实验室 前沿基础研究中心
³ Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, School of Physics and Electronic Science, East China Normal University, Shanghai 200241, China
中国 上海 华东师范大学物理与电子科学学院 纳光电集成与先进装备教育部工程研究中心
⁴ School of Physical Science and Technology, ShanghaiTech University, Shanghai 200031, China
中国 上海 上海科技大学 物质科学与技术学院
⁵ Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China
中国 北京 中国科学院大学 材料科学与光电工程中心
⁶ Shanghai Research Center for Quantum Sciences, Shanghai 201315, China
中国 上海 上海量子科学研究中心
⁷ Hefei National Laboratory, Hefei 230088, China
中国 合肥 合肥国家实验室
Opto-Electronic Advances, 25 July 2024
Abstract

Soliton microcombs, which require the hosting cavity to operate in an anomalous dispersion regime, are essential to integrate photonic systems. In the past, soliton microcombs were generated on cavity whispering gallery modes (WGMs), and the anomalous dispersion requirement of the cavity made by normal dispersion material was achieved through structural dispersion engineering. This inevitably degrades the cavity optical quality factor (Q) and increases pump threshold power for soliton comb generation.

To overcome the challenges, here, we report a soliton microcomb excited by cavity polygon modes. These modes display anomalous dispersion at near-infrared while optical Q factors exceeding 4×10⁶ are maintained. Consequently, a soliton comb spanning from 1450 nm to 1620 nm with a record low pump power of 11 mW is demonstrated, a three-fold improvement compared to the state of the art on the same material platform.
Opto-Electronic Advances_1
Opto-Electronic Advances_2
Opto-Electronic Advances_3
Reviews and Discussions
https://www.hotpaper.io/index.html
Genetic algorithm assisted meta-atom design for high-performance metasurface optics
Physics and applications of terahertz metagratings
Surface-patterned chalcogenide glasses with high-aspect-ratio microstructures for long-wave infrared metalenses
Smart photonic wristband for pulse wave monitoring
Multifunctional mixed analog/digital signal processor based on integrated photonics
Three-dimensional multichannel waveguide grating filters
Ka-Band metalens antenna empowered by physics-assisted particle swarm optimization (PA-PSO) algorithm
Optical micro/nanofiber enabled tactile sensors and soft actuators: A review
Photonics-assisted THz wireless communication enabled by wide-bandwidth packaged back-illuminated modified uni-traveling-carrier photodiode
Highly sensitive and real-simultaneous CH4/C2H2 dual-gas LITES sensor based on Lissajous pattern multi-pass cell
Control of light–matter interactions in two-dimensional materials with nanoparticle-on-mirror structures
High performance micromachining of sapphire by laser induced plasma assisted ablation (LIPAA) using GHz burst mode femtosecond pulses



Previous Article                                Next Article
About
|
Contact
|
Copyright © Hot Paper